Document ID: 9287
Contents
Introduction
Prerequisites
Requirements
Components Used
Conventions
NextPort to MICA Command Translations
EXEC Commands
SPE Configuration Commands
Port Configuration Commands
Testing and Debugging Commands
MICA to Nextport Command Translations
EXEC Commands
SPE Configuration Commands
Port Configuration Commands
Testing and Debugging
NetPro Discussion Forums - Featured Conversations
Related Information
Introduction
This document compares the Software Port Entity (SPE) commands with their equivalent MICA commands.
Prerequisites
Requirements
There are no specific requirements for this document.
Components Used
The information in this document is based on a Cisco AS5400 that runs Cisco IOS® Software Release 12.1(4.1)T.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Conventions
For more information on document conventions, refer to the Cisco Technical Tips Conventions.
NextPort to MICA Command Translations
EXEC Commands
|
Command |
Description |
Equivalent MICA Commands |
|---|---|---|
|
show spe [slot/spe] [slot/spe] |
To show the SPE status. |
None |
|
show spe log [reverse] [slot] |
To show the SPE system log. |
None |
|
show spe modem summary | [slot/spe] [slot/spe] |
To show the modem service history statistics for specified SPEs. |
show modem [slot/port] |
|
show spe modem active [slot/spe] [slot/spe] |
To show the statistics of all active calls on specified SPEs. |
show modem |
|
show spe modem csr [[slot/spe | slot/spe-range] | summary [slot/spe-range]] |
To display the call success rate (CSR) for the specified SPE. |
None |
|
show spe modem disconnect-reason [slot[/spe] [slot[/spe]] | [slot [slot]] [summary] |
To display all modem disconnect reasons for the specified SPEs. |
show modem call-stats |
|
show spe modem high speed [slot[/spe] slot[/spe] [summary] |
To display the total number of connections that have been negotiated within each modulation or coder-decoder (codec) for specific range of SPEs. |
show modem speed |
|
show spe modem high standard [slot[/spe] slot[/spe] [summary] |
To display the total number of connections that have been negotiated within each high modulation or codec for a specific range of SPEs or for all the SPEs. |
None |
|
show spe modem low speed [slot[/spe] slot[/spe] [summary] |
To display the connect-speeds negotiated within each low speed modulation or codec for a specific range of SPEs or for all the SPEs. |
show modem speed |
|
show spe modem low standard [slot[/spe] slot[/spe] | summary] |
To display the total number of connections that have been negotiated within each low modulation or codec for a specific range of SPEs or for all the SPEs. |
None |
|
show spe version [slot[/spe] slot[/spe]] |
To display all MICA and NextPort firmware versions that are stored in Flash, and the firmware assigned to each SPE. |
show modem mapping |
|
show port modem log [reverse] [slot[/port] slot[/port]] |
To display the events generated by the modem sessions. |
show modem log |
|
show port operational-status [slot[/port] slot[/port]] |
To display the statistics of the current active session. |
show modem operational-status |
|
show port config [slot[/port] slot[/port]] |
To display the configuration parameters of the current active session. |
show modem config |
|
clear spe [slot/spe slot/spe] |
To reboot all specified SPEs. All calls will be torn down. |
None |
|
clear spe counters [slot[/spe] slot[/spe]] |
To clear all statistics. |
clear modem counters |
|
clear spe log [slot] |
To clear all log entries for specified SPEs. |
clear modem log |
|
clear port [slot/port slot/port] |
To activate shut and no shut on specified ports. |
clear modem |
|
clear port log [slot/port] [slot/port] |
To clear all log entries for the specified ports. |
clear modem log |
|
show port modem calltracker [slot[/port] slot[/port]] |
To display call tracker information. For details, see Call Tracker plus ISDN and AAA Enhancements for the Cisco AS5300 and Cisco AS5800. |
show modem calltracker |
|
show port modem test [slot[/port] slot[/port]] |
To display port modem test results. |
show modem test |
SPE Configuration Commands
|
Command |
Description |
Equivalent MICA Commands |
|---|---|---|
|
spe country |
To set the system country code. |
modem country |
|
spe log-size |
To set the maximum log entries for each port. |
modem buffer-size |
|
spe poll [auto | time][retry] |
To set the statistic polling interval. |
modem poll |
|
spe call-record |
To generate a modem call record at the end of each call. |
modem call-record |
|
spe [slot/spe [slot/spe]] |
To configure the SPE. |
Already implemented on the AS5300 and AS5800 platforms. |
|
busyout |
To gracefully busy out active calls. |
modem busyout |
|
shutdown |
To tear down all active calls on the specified SPEs. |
modem shutdown |
|
port modem autotest |
To enable modem autotest. |
modem autotest |
|
port modem startup-test |
To run a statup test on all the modems when the system boots up. |
modem startup-test |
|
firmware upgrade [busyout | reboot | recovery] |
To specify the upgrade method. |
Already implemented on the 5300 platform. |
|
firmware location filename |
To specify the firmware file to be upgraded. |
Already implemented on the 5300 and 5800 platforms. |
Port Configuration Commands
|
Command |
Description |
Equivalent MICA Commands |
|---|---|---|
|
port [slot/port slot/port] |
To configure the port range. |
modem range |
|
default [busyout | shutdown] |
To display the value of the command to its default value. |
default modem busyout-threshold |
|
busyout |
To busy out a port. |
modem busyout |
|
shutdown |
To shut down a port. |
modem shutdown |
Testing and Debugging Commands
|
Command |
Description |
Equivalent MICA Commands |
|---|---|---|
|
debug port modem [maintenance] [slot[/spe] slot[/spe]] |
To debug modem maintenance. |
debug modem maintenance |
|
debug spe country |
To display port management SPE country information. |
None |
|
debug spe download-maintenance |
To display port management download maintenance. |
debug modem mica download |
|
debug spe fm |
To debug firmware management. |
debug modem maintenance |
|
debug spe sm |
To debug the SPE state machine. |
None |
|
debug spe modem [error | statistics | trace] |
To display SPE modem statistics. |
debug modem [csm | trace] |
|
debug csm modem [group] [slot/spe] |
To display call switching module (CSM) modem call information. |
debug modem csm |
|
debug csm busyout |
To display CSM busyout events. |
debug csm busyout |
|
debug csm neat |
To display CSM neat events. |
debug csm neat |
|
debug nextport bs [api | cli | detail] |
To debug the NextPort bootstrap. |
None |
|
debug nextport cli |
To test the NextPort command line interface (CLI) unit. |
None |
|
debug nextport ddsm [api | command |detail | response] |
To display the NextPort Digital Data Services Manager. |
None |
|
debug nextport dfc [api | cli | detail] |
To debug the NextPort Dial Feature Card (DFC). |
None |
|
debug nextport est [module | api | data | rcv] |
To debug NextPort EST. |
None |
|
debug nextport fd |
To debug NextPort Formatter and Dispatcher. |
None |
|
debug nextport gdb |
To debug NextPort GDB source code. |
None |
|
debug nextport md [api | callbacks | frame-error | init | oir | rx | throttle] |
To debug the NextPort modem driver. |
None |
|
debug nextport mm [api | cli | detail] |
To debug the NextPort module manager. |
None |
|
debug nextport msmgr [command | detail | response] |
To debug the NextPort modem service manager. |
None |
|
debug nextport np-address |
To complete the address conversion from slot/port to NextPort. |
None |
|
debug nextport secondaryq |
To debug the control message secondary queue. |
debug modem oob |
|
debug nextport siglib [command | detail | response] |
To debug the NextPort Signalling Service Library. |
None |
|
debug nextport spe [api | cli | detail] |
To debug the NextPort SPE Manager. |
None |
|
debug nextport ssm [api | command | detail | oir | response] |
To debug the Nextport Session and Service Manager. |
None |
|
test nextport Bs [crash_info | keepalive] |
To test the bootstrap unit test facility. |
None |
|
test nextport ddsm api [get-llc-parameters | get-state | set-ppp-escape-map] |
To test the DDSM Cisco IOS NextPort Application Programming Interface (API). |
None |
|
test nextport ddsm command [get-llc-parameters | get-running-parms | get-state | set-ppp-escape-map] |
To test the DDSM NextPort command messages. |
None |
|
test nextport EST [add | cmdnak | delete | overflow | read | realtime | reporting | trace | rwite] |
To test the EST Manager unit test facility. |
None |
|
test nextport mm [add | country | crash | delete | downloaded | hiirq | keepalive | loirq | nak1 | nak2 | nak3 | nop | norestart | overflow | qfail | qok | reporting | reset | restart | runtime | secondaryq] |
To test the Module Manager test facility. |
None |
|
test nextport NP-address <1-6> |
To change the number of sessions per SPE. |
None |
|
test nextport recovery threshold <1-10> |
To test the failure count that triggers recovery. |
None |
|
test nextport set [dfc | module | port | slot | spe] number |
To set the test parameters. |
None |
|
test nextport siglib [api | command] |
To test the Signaling Library Unit Test Facility. |
None |
|
test nextport spesm information [buffers | bout [slot[/spe]] |
To test the SPE SM test commands. |
None |
|
test nextport ssm [api | call-back | command | set [base-params | block-enable | params-count | service-type] |
To test the Unit Test Facility. |
None |
|
test port modem back-to-back slot/spe slot/spe |
To execute back-to-back modem tests. |
test modem back-to-back slot/port slot/port |
|
test oir [slot <1-8> [insert | remove]] |
To test online insertion and removal (OIR) simulation. |
None |
|
busyout <slot number> |
To test graceful OIR removal. |
None |
MICA to Nextport Command Translations
EXEC Commands
|
Command |
Description |
Equivalent NextPort Commands |
|---|---|---|
|
show modem [slot/port] |
To show the modem service history statistics for specified SPEs. |
show spe modem summary | [slot/spe] [slot/spe] |
|
show modem |
To show the statistics of all active calls on specified SPEs. |
show spe modem active [slot/spe] [slot/spe] |
|
show modem call-stats |
To display all modem disconnect reasons for the specified SPEs. |
show spe modem disconnect-reason [slot[/spe] [slot[/spe]] | [slot [slot]] [summary] |
|
show modem speed |
To display the total number of connections that have been negotiated within each modulation or coder-decoder (codec) for specific range of SPEs. |
show spe modem high speed [slot[/spe] slot[/spe] [summary] |
|
show modem speed |
To display the connect-speeds negotiated within each low speed modulation or codec for a specific range of SPEs or for all the SPEs. |
show spe modem low speed [slot[/spe] slot[/spe] [summary] |
|
show modem mapping |
To display all MICA and NextPort firmware versions that are stored in Flash, and the firmware assigned to each SPE. |
show spe version [slot[/spe] slot[/spe]] |
|
show modem log |
To display the events generated by the modem sessions. |
show port modem log [reverse] [slot[/port] slot[/port]] |
|
show modem operational-status |
To display the statistics of the current active session. |
show port operational-status [slot[/port] slot[/port]] |
|
show modem config |
To display the configuration parameters of the current active session. |
show port config [slot[/port] slot[/port]] |
|
clear modem counters |
To clear all statistics. |
clear spe counters [slot[/spe] slot[/spe]] |
|
clear modem log |
To clear all log entries for specified SPEs. |
clear spe log [slot] |
|
clear modem |
To activate shut and no shut on specified ports. |
clear port [slot/port slot/port] |
|
clear modem log |
To clear all log entries for the specified ports. |
clear port log [slot/port] [slot/port] |
|
show modem calltracker |
To display call tracker information. For more information, see Call Tracker plus ISDN and AAA Enhancements for the Cisco AS5300 and Cisco AS5800. |
show port modem calltracker [slot[/port] slot[/port]] |
|
show modem test |
To display port modem test results. |
show port modem test [slot[/port] slot[/port]] |
SPE Configuration Commands
|
Command |
Description |
Equivalent NextPort Commands |
|---|---|---|
|
modem country |
To set the system country code. |
spe country |
|
modem buffer-size |
To set the maximum log entries for each port. |
spe log-size |
|
modem poll |
To set the statistic polling interval. |
spe poll [auto | time][retry] |
|
modem call-record |
To generate a modem call record at the end of each call. |
spe call-record |
|
spe [slot/spe slot/spe] (Already implemented on the AS5300 and AS5800 platforms.) |
To configure the SPE. |
spe [slot/spe [slot/spe]] |
|
modem busyout |
To gracefully busyout active calls. |
busyout |
|
modem shutdown |
To tear down all active calls on the specified SPEs. |
shutdown |
|
modem autotest |
To enable modem autotest. |
port modem autotest |
|
modem startup-test |
To run a statup test on all the modems when the system boots up. |
port modem startup-test |
|
firmware upgrade [busyout | reboot | recovery] (Already implemented on the 5300 platform.) |
To specify the upgrade method. |
firmware upgrade [busyout | reboot | recovery] |
|
firmware location filename (Already implemented on the 5300 and 5800 platforms.) |
To specify the firmware file to be upgraded. |
firmware location filename |
Port Configuration Commands
|
Command |
Description |
Equivalent NextPort Commands |
|---|---|---|
|
modem range |
To configure the port range. |
port [slot/port slot/port] |
|
default modem busyout |
To display the value of the command to its default value. |
default [busyout | shutdown] |
|
modem busyout |
To busy out a port. |
busyout |
|
modem shutdown |
To shut down a port. |
shutdown |
Testing and Debugging
|
Command |
Description |
Equivalent NextPort Commands |
|---|---|---|
|
debug modem maintenance |
To debug modem maintenance. |
debug port modem [maintenance] [slot[/spe] slot[/spe]] |
|
debug modem mica download |
To display port management download maintenance. |
debug spe download-maintenance |
|
debug modem maintenance |
To debug firmware management. |
debug spe fm |
|
debug modem [csm | trace] |
To display SPE modem statistics. |
debug spe modem [error | statistics | trace] |
|
debug modem csm |
To display call switching module (CSM) modem call information. |
debug csm modem [group] [slot/spe] |
|
debug csm busyout |
To display CSM busyout events. |
debug csm busyout |
|
debug csm neat |
To display CSM neat events. |
debug csm neat |
|
debug modem oob |
To debug the control message secondary queue. |
debug nextport secondaryq |
|
test modem back-to-back slot/port slot/port |
To execute back-to-back modem tests. |
test port modem back-to-back slot/spe slot/spe |
NetPro Discussion Forums - Featured Conversations
| NetPro Discussion Forums - Featured Conversations for Access |
| Network Infrastructure: Remote Access |
Related Information
- Dial Technology Support Page
- Managing Port Services on the Cisco AS5400 Universal Access Server
- Managing and Troubleshooting the Universal Port Dial Feature Card
- Technical Support - Cisco Systems
| Updated: Nov 15, 2007 | Document ID: 9287 |